Standard cutter to cut transparencies, masking films or thin foils.Sharpening angle: 45°Offset: 0,25mm

Cutter knives with special hardened cut surface for transparencies, masking films or thin foilsOffset: 0,25mm

Holder for cutter blades for Roland printers

OEM spare part with solvent resistant hose

Compatible spare part without tube connection.

Original spare part including connection tubes.

Connector M7 for damper. Compatible with Mutoh and Roland.

Connection for big hoses with 2,8 mm inner diameter.

Damper for Mimaki, Mutoh and RolandSuitable for the following large format printers:Mutoh ValueJet 1324, 1604, 1608, 1614, 1617, 1624, 1626, 1628, 1638, 1924, 1938, 2638Mimaki JV34Roland RA-, RE-, RF-, VS(i)-, XF-, XR-SerieOcé CS9160

The damper is an original spare parts, no remake!Suitable for the following wide format printers:Roland CammJet CJ-400, 500, FJ-40, 42, 50, 52, SolJet SC-500, SJ-500, 600Roland HiFi Jet FJ-400, FJ-500, FJ-600

Connection for a big hose with 2,8 mm inner diameter.Good reproduction. Similar to the original.

Connection for hoses with 2,0 mm internal diameter.Solvent resistant housing Solvent resistant, red sealing ring Big strainer for improved flow featuresCompatible spare part

Connection for hoses with 2,8 mm inner diameter.The big filter sieve prevents the ink flow to stop during high printing speed.Alternative damper.

Connection for hoses with 2,0 mm inner diameter.The big filter sieve prevents the ink flow to stop during high printing speed.

With solvent resistant hose. Reproduction. Not original.OEM spare part numbers (comparison purposes only):Mutoh spare part no.: ME-80077, KY-80077, MY-81854, KY-81854Roland spare part no.: 1000004546, 1000002794

For repair of damaged print heads or for modification of water-based printhead into solvent resistant.Inclusive sealing ring

Original spare part with original Head-ID. New version!The Head-ID is necessary for the flawless action of the printhead. Without the ID the print head is not printing properly, wears out faster and is damaged earlier.Since 2019 we deliver the enhanced version of this printhead which is among others better resistand against UV ink.Mimaki spare part no.: M004905Roland spare part no.: 6000005213 (old version 1000002201)For printheads payment by PayPal is not possible.

Original print head!For self installation, we assume no warranty.Mutoh spare part no.: DG-43988, DG-42987, DG-42771, DG-43345Roland spare part no.: 6701409010For printheads payment by PayPal is not possible.

Sponge for flush box. Has to be changed together with Filter Serge Mist Under (next article below).

Flow sponge under Filter Serge Mist, should be changed together.

Cable to connect printhead to headboard.

Length: 27cmThe flat ribbon cable is suitable for the following wide format printers:Agfa Sherpa 43, 54, 62Brunner / Spandex Jetster 43 and 62Kodak 3038, 3043, 3062Mimaki JV2Mutoh RJ-800, RJ-4100Mutoh RJ-6100Mutoh Rockhopper 38Mutoh Rockhopper IRoland CammJet CJ-400, 500, FJ-40, 42, 50, 52, SolJet SC-500, SJ-500, 600

Length: 27cmThe flat ribbon cable is suitable for the following wide format printers:Agfa Sherpa 43, 54, 62Brunner / Spandex Jetster 43 and 62Kodak 3038, 3043, 3062Mimaki JV2Mutoh RJ-800, RJ-4100Mutoh RJ-6100Mutoh Rockhopper 38Mutoh Rockhopper IRoland CammJet CJ-400, 500, FJ-40, 42, 50, 52, SolJet SC-500, SJ-500, 600

Roland spare parts no: 1000006702For one Roland VS-, RE- and RA-Roland printhead you need 3 of this cables and one of our part no. FLACH-29-276.For one XF-640 Roland printhead you need 4 of this cables.Contact on the same side of the cable